HIPLOT Plotter Driver for Windows Houston Instrument, A Division of Summagraphics Corporation Version 2.40 The HIPLOT device driver allows a Houston Instrument plotter to be used as a printer under Windows versions 3.0, 3.1 and Windows 95. The HIPLOT driver supports the following features: +) Over twenty different plotter models including cutters. +) DM/PL, HP-GL and HP-GL/2 plotter languages. +) Color sorting. +) Color mapping (driver chooses closest available color). +) Draft and final velocity settings per plotter pen. +) Pen and paper prompts. +) Long plots (User specified paper length). +) Multiple copies. +) Scaling. +) Device fonts. +) True Type font support (filled or not filled). +) Wide lines. +) High and low resolution modes. INSTALLATION The following steps are intended to be a brief overview of how to install the HIPLOT plotter driver. For complete instructions, refer to your Windows User's Guide. Windows 3.0 installation 1) Run Windows and from the Control Panel, choose Printers. 2) Select "Add" printer. 3) Under the list of available printers, select "Unlisted Printer." 4) Install the driver disc into drive A or B, then select this drive under directories, then select the HIPLOT directory. The driver HIPLOT.DRV should appear under Driver Files. Select HIPLOT.DRV and then select OK. 5) Select "HI Plotter" under Installed Printers, then select "Configure" to configure the driver for your particular plotter model. 6) First choose the port to which the plotter is attached, then select "Setup." Note: Driver configuration data is saved in the WIN.INI file on a per port basis. If you select a different port at a later date, you will need to reconfigure the driver for that particular port via "Setup." 7) Select your plotter model from the available models under the "Plotter Models" list box. Next, select "Media" and choose a paper size under the "Medias" list box. Note: The paper size selected under medias MUST match the paper size used in the plotter. 8) Select "Pens" to configure the pen attributes (size, type, color, draft speed and final speed). 9) To make the "HI Plotter" the default printer, make sure it is selected under Installed Printers (Printers Dialog Box) and select "Active" under Status. Now double click on "HI Plotter" to make it the default printer. 10) If the plotter is connected to a serial port, choose Ports from the Control Panel and configure the port to match the plotters communication parameters. If you have selected HP-GL as the plot language, the plotter and port must to be set to hardware handshake. If DM/PL or HP-GL/2 was selected, xon/xoff or hardware handshake may be used. Windows 3.1 installation 1) Run Windows and from the Control Panel, choose Printers. 2) Select "Add" printer. 3) Under the list of available printers, select "Install Unlisted or Updated Printer." 4) Select "Install." 5) Install the driver disc into drive A or B, then enter A:\HIPLOT or B:\HIPLOT. 6) When "Houston Instrument Plotter" is displayed, select "OK." 7) To make "Houston Instrument Plotter" the default printer, select "Set As Default Printer." 8) Select "Connect" to specify port settings. Note: Driver configuration data is saved in the WIN.INI file on a per port basis. If you select a different port at a later date, you will need to reconfigure the driver for that particular port via "Setup." 9) Select "Setup" to configure the driver. First specify your plotter model from the available models under the "Plotter Models" list box. Next, select "Media" and choose a paper size under the "Medias" list box. Note: The paper size selected under medias MUST match the paper size used in the plotter. 10) Select "Pens" to configure the pen attributes (size, type, color, draft speed and final speed). 11) If the plotter is connected to a serial port, choose Ports from the Control Panel and configure the port to match the plotters communication parameters. If you have selected HP-GL as the plot language, the plotter and port must to be set to hardware handshake. If DM/PL or HP-GL/2 was selected, xon/xoff or hardware handshake may be used. SPECIAL NOTES: +) If you are using a DMP-160 series plotter, you will need to change the Chart Commands menu item to "DMP-60 EH/EF" in the Configuration Menu. This allows the driver to change between portrait and landscape modes. If this feature is not enabled, only landscape mode is available. This only applies if you are using the DM/PL plotter language. If you are in Automatic Roll mode, only landscape is available regardless of this menu setting. Note: Chart Commands is only available when the plotter is in Service Mode. Service Mode is entered by holding down the Reset/Load and Online key during powerup (letter s visible in upper right corner of display). For more information on Service Mode, refer to your DMP-160 series plotter manual. +) If a chart size can be loaded as either half chart or full chart, load the chart as full chart. An example is a D size chart on an E size plotter. The plotter's pinch roller should be set to the D size position (NOT the E position) and the chart loaded as full chart. +) If you have a DMP-29 with ROM revision 003, you will need to upgrade your plotter's ROMs to the latest revision. ROM revision 003 doesn't work correctly with this driver. +) If you receive the message "Error allocating segment for plot data!", this indicates that your system doesn't have enough memory to store plot data. If color sorting is enabled, try plotting again with color sorting disabled. +) If you receive the message "Error writing plot data to file!", this indicates that the drive that Windows uses for temporary files is full. This message should only appear if you have color sorting enabled and system memory is low. +) If you receive the message "The Print Manager cannot write to COM#", increase the Transmission Retry value to 150 or more in the Printers Configure dialog box. +) If you have a cutter, you will not get filled curves, polygons or text. +) If you have a DMP-69C cutter/plotter and it is configured for HP-GL, the HP-GL origin must be configured to CENTERED. +) If you have any problems installing or running the HIPLOT plotter driver, call Technical Support at TMS 714-837-2324. Windows 95 installation 1) Go to "my computer" 2) Click on printers add a printer local printer 3) Click on have disk. Put disk in drive. 4) Press return or OK 5) Click on HIPLOTTER. 6) Keep directory. 7) Select port you will be using for plotter. 8) Default printer (yes or no). 9) Do you want to print a test page (yes or no). 10) Finish. VERSION 1.10: *** CHANGES *** 1) Added support for the JetPro Series V100 printer/plotter. 2) The driver now supports pen prompting while color sorting is disabled. *** CORRECTIONS *** 1) Text produced by Microsoft Project is not clipped properly. Fixed in version 1.10. 2) Invalid plot files are produced if HP-GL/2 is selected and color sorting is enabled. Fixed in version 1.10. 3) Hatch patterns are not always updated correctly if DM/PL is selected. Fixed in version 1.10. 4) Plots have additional lines when using RN-PDC (Radial Network - Protective Device Coordination System) software. Fixed in version 1.10. VERSION 1.20: *** CHANGES *** 1) Added support for the JetPro Series V50 printer/plotter. *** CORRECTIONS *** 1) Multiple copies doesn't work if a V100 is selected and the plot language is HP-GL/2. Fixed in version 1.20. VERSION 1.30: *** CHANGES *** 1) Added support for the DMP-100C cutter/plotter. 2) Added support for the DMP-69C cutter/plotter. VERSION 1.30S: *** CORRECTIONS *** 1) Horizontal and vertical lines (wide) are not always plotted. Fixed in version 1.30S. 2) The driver's setup dialog box will not always display when the Options button is selected in the Printer Setup dialog box. Fixed in version 1.30S. VERSION 1.40: *** CHANGES *** 1) Added support for HIPLOT series plotters. 2) Added support for device/driver multiple copy control. 3) Added support for english or metric units. VERSION 1.41S: *** CORRECTIONS *** 1) The driver will always use the SEND Copy Mode regardless of the Copy Mode setting. Fixed in version 1.41S. VERSION 2.00: *** CHANGES *** 1) Added support for True Type fonts. 2) Added support for Summachrome series printers. 3) The "Pen Settings" dialog box now includes a gray pen. 4) The "Reset All Pens" button in the "Pen Settings" dialog box will default the pen colors as follows: Red, Yellow, Green, Turquoise (Cyan), Blue, Magenta, Black and Gray. 5) The driver will search the pen carousel for the pen with the closest width when drawing wide lines. 6) The maximum plot length for V50/V100 printer plotters has changed from 120 to 182 inches. 7) The maximum width for V100 printer plotters when configured with the roll option has changed from 11.0 to 14.8 inches. *** CORRECTIONS *** 1) Plots have additional lines when plotting text from TurboCAD software. Fixed in version 2.00. 2) Objects created with a solid linestyle are not plotted when using Lotus Freelance. Fixed in version 2.00. 3) The hard clip limits are not reported correctly when using Drafix Windows CAD. Fixed in version 2.00. 4) HP-GL/2 plots with vector lengths longer than 81 inches are not plotted correctly. Fixed in version 2.00. 5) Printing from Quicken (version 3.0) will cause a UAE. Fixed in version 2.00. VERSION 2.20: *** CHANGES *** 1) Final and Draft mode now controls the number of points used for True Type characters. For Draft Mode, fewer points are used. 2) The maximum plot length for V50/V100 printer plotters has changed from 182 to 163 inches. 3) The maximum plot length for DMP40, DMP50, DMP60, DMP160 and HI7000 series plotters has changed from 120 to 163 inches. 4) Added support for the SummaSign series cutters. *** CORRECTIONS *** 1) Text is not plotted correctly when using applications that don't support True Type fonts. Fixed in version 2.20. 2) True Type fonts are not plotted from Corel Draw when the driver is configured for a cutter. Fixed in version 2.20. 3) The A0 paper size is not displayed with the correct metric dimensions. Fixed in version 2.20. 4) Final and Draft mode is disabled for raster devices. Fixed in version 2.20. VERSION 2.30: *** CHANGES *** 1) The driver now defaults to low resolution. 2) All raster graphics are output as a black rectangle with a diagonal line. Pen plotters are not capable of printing raster graphics. *** CORRECTIONS *** 1) Some True Type characters do not plot correctly when using Microsoft Word. Fixed in version 2.30. 2) Some True Type characters have jagged edges. Fixed in version 2.30. 3) Polygons in Corel Draw are not always plotted correctly. Fixed in version 2.30. 4) Plots produced on DMP-40 and DMP-50 series plotters have the wrong colors when pen prompting and color sorting are enabled in the driver. Fixed in version 2.30. VERSION 2.40: *** CORRECTIONS *** 1) Some plotters models report syntax errors when using Visual CADD 1.1. Fixed in version 2.40.